Ultrabrights 2-in-1 LED Brake Light/Turn Signal Upgrades for newer BMW Motorcycles (S series, G series, R series and F series)

2-in-1s-brake-turn-new-BMW.jpg
weiser-brake-light-blinker-upgrade-new-bmw-1.jpg
weiser-brake-light-blinker-upgrade-new-bmw-2.jpg
weiser-brake-light-blinker-upgrade-new-bmw-3.jpg
2-in-1s-brake-turn-new-BMW.jpg
weiser-brake-light-blinker-upgrade-new-bmw-1.jpg
weiser-brake-light-blinker-upgrade-new-bmw-2.jpg
weiser-brake-light-blinker-upgrade-new-bmw-3.jpg

Ultrabrights 2-in-1 LED Brake Light/Turn Signal Upgrades for newer BMW Motorcycles (S series, G series, R series and F series)

249.00

These 2-in-1 LED Brake Light/Turn Signal upgrades are the brightest, safest and simplest lighting solutions available. Designed specifically for newer BMW motorcycles, this product fits right inside the rear wheel OEM indicator housing - no need for brackets, drilling or clamping. A full fitting kit is included with all components labelled and coded, along with the required wiring instructions and circuit diagram. Full written instructions are also included. 

  • Added safety
  • Designed to give a very high intensity light performance in all weathers
  • Designed specifically for BMW bikes
  • Fits neatly into the original housing
  • No need for additional external fitting
  • Designed to work with your bike’s electronics
  • No need for brackets, drilling or clamping
  • Adds ultra-minimal weight to your bike
  • Takes just 30 minutes to an hour to fit
  • Very easy to replace if you drop your bike
  • More effective and more affordable than other options
  • Low cost or expensive bike, this solution fits them all

Ultrabrights are manufactured in the USA and UK.

This packet contains both left and right lights.

Bike Model:
Quantity:
Add To Cart

Combined in an intelligent electronic circuit board design, this innovative LED upgrade has 24 powerful automotive standard LEDs: 12 intense red LEDs for the brakes together with 12 ultra-orange amber LEDs for the turn signal.

Weiser’s 2-in-1 LED Brake Light/Turn Signal upgrades are designed to light up alongside your existing brake light – so you have three brake lights for maximum safety. Better still, these two extra bright intensely red brake lights are much, much brighter than the existing rear light. This means that following traffic will be alerted to your braking far more quickly and effectively than with just the standard brake lights alone - helping you to avoid a rear end collision into your bike.

These extra brake lights are also your turn signals – all from the same unit. When braking, flick your turn signal switch to the right and the right hand brake light will be replaced with an extra bright amber, flashing turn signal to show you’re turning right. After the maneuver, cancel the switch and the intelligent electronics return the rear light to brake mode ready to respond to your next braking maneuver.

These Ultrabrights are suitable for the following BMW bikes:
R1200RS (2015 and up)
R1200R (2015 and up)
R1200GS (2013 and up)
R1200GS LC Adventure (2014 and up)
R nineT (2014 and up)
R nine T Pure (2016 and up)
R nine T Scrambler (2016 and up)
R nine T Urban G/S (2017 and up)
F700GS (2015 and up)
F800GS (2015 and up)
F800GS Adventure (2015 and up)
F800GT (2013 and up)
G310R (2015 and up)
G450X (2008 and up)
G650X (2006 and up)
G650GS (2011 and up)
K1300S (2015 and up)
S1000RR (2009 and up)
S1000XR (2016 and up)
S1000R (2014 and up)

Each pack contains:
2x LED Brake Light/Turn Signal upgrades
2x wires marked 'Weiser' at one end and '3-in-1 at the other end. These wires will join together using item 7 and item 3 to provide the power to your Weiser brake lights.
1x relay. The relay takes power direct from the battery and switches it to your Weiser brake lights/turn signals to ensure the CAN bus will not flag any faults.
1x wire marked 'Relay 87' at one end and '3-in-1' at the end. This wire will take 12v from the relay to join with item 1 to provide the power to your Weiser brake/turn lights.
1x wire with fuse holder marked 'Relay 30' at one end and 'Battery +Ve' at the other. This is providing the +12v to the relay so that it can be switched to your brake/turn lights when the brakes are applied.
1x wire marked 'Bike Earth' at one end and 'Relay 85' at the other. This wire provides the -VE to the relay.
1x wire marked 'Relay 86' at one end and is unmarked at the other. This wire connects the relay to the +12v supply that provides power to the brake light using the Posi-Tap (item 8) provided.
1x Posi-Twist connector - see instructions on how to use this also on this page.
1x Posi-Tap connector - see instructions on how to use this also on this page.
1x 5 amp fuse - do not fit any other value fuse.
5x tie wraps - use these to secure the wires you are installing as instructed.
2x locking keys for securing the turn signal housing (not an essential requirement).